Broken gadgets are a sad reality, but they aren't the end of the road. Just because you dropped your phone in a puddle or your laptop got run over by a car doesn't mean you have to scrap it or buy another one. There's plenty of ways you can still repair your gadget and get it working again. Your favourite gadget might even be salvageable...
{tocify} $title={Table of Contents}
1. 5 Injured Gadgets You Can Still Fix
We all make mistakes, and sometimes that means we break our gadgets. If you’ve got an injured gadget, follow these steps to figure out how to fix it. 1) If you broke your gadget, look at the damage.Try to determine if you’ve caused any permanent damage to your gadget.
2) Clean your gadgets thoroughly. You should probably read and follow the instructions on the item’s manual before you open it to see if you’ve damaged anything. If your gadget was battery-powered, make sure you juice it up first. If it was a stereo, check that there are no exposed wires sticking out. These can be bent or damaged by being plugged in or other accessories.
3) Read the user manual. Pull out the user manual and read through it. If the instructions say something about replacing parts, read that time and again. Follow the directions exactly.
4) Look closer at your gadget. Next, take a closer look at the specs. If it has a battery and a solid-state drive, get an RC car bucket or a camera. Make sure to include the correct lens and included wires in the specs. If your gadget was a TV, look at the signal strength and HDMI port, if available.
5) Look at the internals. Interiors can often be difficult to inspect and repair. You might want to remove the console and check for cables and connections. Look at the CPU, screen, and battery. Disconnect the battery if you are working on the back of the device. If you can access the internals, check to make sure electricity is not all flowing to the wrong place.
6) Repair the device to its original working order. Drain and refill any battery that is attached to the device, change the battery if it is damaged, and reinstall the device’s software. If your gadget is still running but becomes unstable or refuses to turn on, it definitely isn’t working the way it used to. That’s not repairable.
2. What to Do When Your iPhone Gets Wet
If you’re not using a protective case on your iPhone, then it’s inevitable that you’re going to drop it at some point - after all, it’s a pretty slippery device. If it does happen to fall into water, you’re going to want to do everything you can to get it out as fast as possible.
A drop or two isn’t going to kill your phone. But if it’s consistently being damaged, it’s time to take matters into your own hands. Ah, the classic case solution. You’ve got your screwdriver, you’ve got wads of tissues, but something still chokes. It thrashes against the sides of the box when you try to pry it open.
The case might be broken or glued onto the phone, rendering it difficult to remove. These days, wireless chargers are becoming cheaper and more flexible. You can stick several of these into your phone (or even attach a phone stand if you’re mobile) to give it stability in the event your device trips over a prop or is otherwise uncentred. It’s also worth mentioning some cases are even made with a mesh inside which cushions the impact of dropping your phone.
One of the simplest techniques anyone can replicate is to simply lubricate the inside before putting your fingers inside. Setting lube on a cotton bud or squirt bottle usually does the trick for most hands. After taking care of the inside, it’s time to look at the outside.
Obviously, there are going to be all sorts of signs your gadget is broken. And we aren’t going to spend much time on this — you can find everything you need to know at iFixit (if it’s not there, you should know how to fix it). What you care about are the two main points on the outside that let you know your gadget is broken. The first is a capacitor which is quite simply, a metal element used to monitor and control the charge flow in a circuit. Capacitors can break quite easily, especially if they get hit by static electricity.
Read More Details: What Is Internet Computer Coin And How Does It Work?
3. How to Repair a Cracked Cell Phone Screen
To repair a cracked cell phone screen, you'll need the following items: a suction cup, a credit card, a bowl of rice, a bowl of water, a towel, a cell phone repair kit, and a small screwdriver.
First, place the bowl of rice on a towel on a flat surface.Then, use the credit card and the screwdriver to open the phone’s case. You should be able to easily wiggle the phone’s antenna loose from the circuit board.
Next, you’ll need to take the adhesive off the adhesive backing from the circuit board. Using the water, gently drip and pull the sticky tape off the adhesive, exposing the underlying circuit board. Finally, add the rice to the remaining liquids and mix thoroughly.
The best way to ensure a even coating is to evenly wet the wet rice with the remaining water you’ve been using. Before moving on, make sure you wipe down the sticky adhesive in the bowl you’re using with a cotton bud or rag. Now, mix the repaired adhesive with enough water to make a thick paste. Apply the paste to the circuit board fully covering the adhesive and circuit board with a drop or two of the mixed paste.
Allow the attempt to dry for a few minutes, then put the device back together, reconnect the antenna to the board, and test it out. Don’t forget to rinse and repeat if needed. If your gadget made it this far, congratulations! But there still may be some tedious steps left for you to take before you can feel confident that your phone is back in action and not just another banged-up hunk of plastic.
While it isn’t strictly necessary to start every repair process from the beginning, you’d be surprised at how often people skip this step, only to have to fix their broken gadget several months down the road. It’s a nightmare to go back and forth between working on a device and taking it apart for the diagnostic tests to prove that it’s really broken.
4. The Best Way to Fix a Broken Computer Screen
Since glass is a brittle material, it’s easy to break a computer screen. Here’s a quick guide to the best way to fix a broken computer screen: 1. Turn off the computer 2. Carefully remove the computer cover 3. Inspect the computer screen 4. Repair or replace the broken screen 5. Put the computer back together 6.Enjoy your new gadget The best place to start when repairing your broken gadget or computer is at the source.
Fortunately, most items will come with instructions, and sometimes you can even find an official repair guide online. If you can’t find the replacement part you need there, a good place to start is the website iFixit, which will mail you replacement parts as soon as they are available. As well as buying parts, you can even order components online and have them arrive to you.
While iFixit is a great place to start, it doesn’t always have the perfect replacement part. It’s not uncommon for a product to be worth more than its original price at the time it was bought or sold, so it’s impossible to sell it for as little as you paid for it.
Again, iFixit has a great guide to help you determine what the right replacement part is for your device, with 10 different criteria: iFixit is a crowdsourced website, so a small number of items are behind unpaid queue and take time to be delivered.
If your broken gadget has been waiting for a while without being said to be worth replacing then it might be worth calling the iFixit team for a quote. You won’t be charged anything for this, but it’s quicker than trying to fly around the world to get an estimate.
iFixit has an excellent reputation for fast delivery, so if your parcel isn’t there a few days later you can be pretty confident they knew it when they sent it. There are many websites that sell refurbished gadgets online, although they are branded and have space reserved for a price.
5. How to Repair a Broken Laptop Screen and Other Physical Damage
1. You can fix a broken laptop screen by ordering a new screen online or at your local electronics store.
2. The first step to replacing the screen is to remove the plastic bezel.
3. Remove the screws that hold the screen in place.
4. Be careful when removing the screen.
5.If the case covers the entire back of the device, you can carefully detach it by prying up and then pulling away with a small pair of pliers.
6. Check to see if the screws needed to hold the screen in place all the way around are compatible.
7. Before you buy a phone case, ensure it’s compatible with the device you’re planning on using it with.
8. If you’re not sure you can successfully repair a device, repair guides from iFixit and MacRumors can help you find a solution.
9. Check to see if you have all the right tools to carefully remove the screen.
10. If you need replacement parts, you can find them at places like Rose county electronics recyclers.
11. If you have a face or touch screen, it’s important to get gloves and safety glasses as you may have a phobia around touching glass.
12. Dry the device completely after repairs to avoid any smudging of the repair.
13. Change the batteries if you have a modern phone. An old phone battery may give you more trouble than a newer one.
14. Check to see if software updates or security patches are installed and if you need them. Go here to find the download links for iOS, Chrome and Android.
15. Open up the case for your device, and carefully remove all the components that were supposed to come with it. This can include the battery and any internal components.
16. Fit the components in slots and screw them together, making sure the screws are all the way in.
17. Add new components to the device.
18. Test everything works by inputting some commands. Screen fix, Bluetooth keyboard, screen brightness, volume and some other settings.
0 Comments